Das Forum von www.k-ue.de und www.1600i.de
Login Registrieren FAQ Mitgliederliste Suchen Das Forum von www.k-ue.de und www.1600i.de Foren-Übersicht

injector spec

 
Neues Thema eröffnen   Neue Antwort erstellen    Das Forum von www.k-ue.de und www.1600i.de Foren-Übersicht » Technique - Technik
Auflagepunkte Hebebühne :: Getriebe -Pendelachsen wieder einbauen bzw eintreiben  
Autor Nachricht
xbacax



Anmeldungsdatum: 11.10.2007
Beiträge: 44
Wohnort: Kozmin Wlkp.

BeitragVerfasst am: 30 Okt 2010 12:21    Titel: injector spec Antworten mit Zitat

hi,

can anyone please tell me the spec of mexi injectors ?
size, flow and everything.

also, are there any alternative injectors to replace the original ones ?

thanks
baca
Nach oben
espresso



Anmeldungsdatum: 18.11.2009
Beiträge: 43
Wohnort: Baden-Württemberg

BeitragVerfasst am: 05 Nov 2010 15:53    Titel: Antworten mit Zitat

Hi xbacax,
you want to mount the mexi injectors into your single throttle bodies? They fit there (you only have to cut out a piece of your side panels).


Many greetings
espresso


Nach oben
xbacax



Anmeldungsdatum: 11.10.2007
Beiträge: 44
Wohnort: Kozmin Wlkp.

BeitragVerfasst am: 28 Nov 2010 3:19    Titel: Antworten mit Zitat

not really Wink

my problem was that one of the original injectors has been broken. Instead of ordering set of new ones, I'll try to install 1.8 T 1997 Audi injectors Smile they should be ok with engine spec and individual TBs Wink

best wishes
baca
Nach oben
Red1600i



Anmeldungsdatum: 07.10.2007
Beiträge: 416
Wohnort: Bogen

BeitragVerfasst am: 28 Nov 2010 11:04    Titel: Antworten mit Zitat

You will have a lot of fun with these 1.8T injectors. Do you think, this little 50PS 1600i motor will run with 317ccm turbo injectors of a 180PS car? They just look the same but they have 2x the volume.

No way... or you have a turbo installed and a free programmable controller...


Nach oben
xbacax



Anmeldungsdatum: 11.10.2007
Beiträge: 44
Wohnort: Kozmin Wlkp.

BeitragVerfasst am: 10 Dez 2010 14:17    Titel: Antworten mit Zitat

Red1600i hat folgendes geschrieben:
You will have a lot of fun with these 1.8T injectors. Do you think, this little 50PS 1600i motor will run with 317ccm turbo injectors of a 180PS car? They just look the same but they have 2x the volume.

No way... or you have a turbo installed and a free programmable controller...


well, not realy 317ccm, I 've bought those with something around 240ccm, but you're right they squirts way too much Wink
altough, guy whoose about to tune it on my megasquirt said that there is no problem if they are too big, couse he will just decrease the dose

hope it's gonna be ok

regards Wink
baca
Nach oben
Beiträge der letzten Zeit anzeigen:   
Neues Thema eröffnen   Neue Antwort erstellen    Das Forum von www.k-ue.de und www.1600i.de Foren-Übersicht » Technique - Technik Alle Zeiten sind GMT + 1 Stunde
Seite 1 von 1

 
Du kannst keine Beiträge in dieses Forum schreiben.
Du kannst auf Beiträge in diesem Forum nicht antworten.
Du kannst deine Beiträge in diesem Forum nicht bearbeiten.
Du kannst deine Beiträge in diesem Forum nicht löschen.
Du kannst an Umfragen in diesem Forum nicht mitmachen.
Du kannst Dateien in diesem Forum nicht posten
Du kannst Dateien in diesem Forum nicht herunterladen




(co) 2011 www.1600i.de
Hosted by 1600i.de


phpBB Template by Vjacheslav Trushkin